Julian's Science Experiments
  • Famous Experiments and Inventions
  • The Scientific Method
  • Home Aviation Experiments Aviation Science Fair Projects Famous Aviators Warning!
       

    Fuselage, Empennage & Trim Tabs
    Experiments and Background Information







    Experiments

    Fuselage, Empennage & Trim Tab

    Definitions

    The fuselage is an aircraft's main body section that holds crew and passengers or cargo.

    Empennage is an aviation term used to describe the tail portion of an aircraft.

    Trim tabs are small surfaces connected to the trailing edge of a larger control surface on a boat or aircraft. The angle of the tab relative to the larger surface can be adjusted to null out hydro- or aero-dynamic forces and stabilise the boat or aircraft in a particular desired attitude without the need for the pilot to constantly apply a control force.

    Topics of Interest

    The fuselage (from the French fuselé "spindle-shaped") is an aircraft's main body section that holds crew and passengers or cargo. In single-engine aircraft it will usually contain an engine, although in some amphibious aircraft the single engine is mounted on a pylon attached to the fuselage which in turn is used as a floating hull. The fuselage also serves to position control and stabilization surfaces in specific relationships to lifting surfaces, required for aircraft stability and maneuverability.

    Box truss structure: The structural elements resemble those of a bridge, with emphasis on using linked triangular elements. The aerodyamic shape is completed by additional elements called formers and stringers and is then covered with fabric and painted. Most early aircraft used this technique with wood and wire trusses and this type of structure is still in use in many lightweight aircraft using welded steel tube trusses. This method is especially suitable for amateur-built aircraft kits, where a complete welded truss structure is delivered with the fitting of other components, covering, and finishing completed by the user, as it ensures that a robust, uniform load bearing structure is within the completed aircraft.

    Geodetic construction: Geodetic structural elements were used by Barnes Wallis for British Vickers between the wars and into World War II to form the whole of the fuselage, including its aerodynamic shape. In this type of construction multiple flat strip stringers are wound about the formers in opposite spiral directions, forming a basket-like appearance. This proved to be light, strong, and rigid and had the advantage of being made almost entirely of wood. The structure is also redundant and so can survive localized damage without catastrophic failure. A fabric covering over the structure completed the aerodynamic shell (see the Vickers Wellington for an example of a large warplane which uses this process). The logical evolution of this is the creation of fuselages using molded plywood, in which multiple sheets are laid with the grain in differing directions to give the monocoque type below.

    Monocoque shell: In this method, the exterior surface of the fuselage is also the primary structure. A typical early form of this (see the Lockheed Vega) was built using molded plywood, where the layers of plywood are formed over a "plug" or within a mold. A later form of this structure uses fiberglass cloth impregnated with polyester or epoxy resin, instead of plywood, as the skin. A simple form of this used in some amateur-built aircraft uses rigid expanded foam plastic as the core, with a fiberglass covering, eliminating the necessity of fabricating molds, but requiring more effort in finishing (see the Rutan VariEze). An example of a larger molded plywood aircraft is the de Havilland Mosquito fighter/light bomber of World War II. It should be noted that no plywood-skin fuselage is truly monocoque, since stiffening elements are incorporated into the structure to carry concentrated loads that would otherwise buckle the thin skin. The use of molded fiberglass using negative ("female") molds (which give a nearly finished product) is prevalent in the series production of many modern sailplanes. The use of molded composites for fuselage structures is being extended to large passenger aircraft such as the Boeing 787 Dreamliner (using pressure-molding on female molds).

    Semi-monocoque: Sectioned fuselage of a Boeing 747 showing frames, stringers and skin all made out of AluminiumThis is the preferred method of constructing an all-aluminum fuselage. First, a series of frames in the shape of the fuselage cross sections are held in position on a rigid fixture, or jig. These frames are then joined with lightweight longitudinal elements called stringers. These are in turn covered with a skin of sheet aluminum, attached by riveting or by bonding with special adhesives. The fixture is then disassembled and removed from the completed fuselage shell, which is then fitted out with wiring, controls, and interior equipment such as seats and luggage bins. Most modern large aircraft are built using this technique, but use several large sections constructed in this fashion which are then joined with fasteners to form the complete fuselage. As the accuracy of the final product is determined largely by the costly fixture, this form is suitable for series production, where a large number of identical aircraft are to be produced. Early examples of this type include the Douglas Aircraft DC-2 and DC-3 civil aircraft and the Boeing B-17 Flying Fortress. Most metal light aircraft are constructed using this process.


    Empennage is an aviation term used to describe the tail portion of an aircraft. ("Empennage", "tail", and "tail assembly" may be interchangeably used.) The empennage gives stability to the aircraft and controls the flight dynamics: pitch and yaw. In simple terms the empennage may be compared to the feathers of an arrow, colloquially; "Tail Feathers"

    Structurally, the empennage consists of the entire tail assembly, including the fin, tailplane and the part of the fuselage to which these are attached. On an airliner this would be everything behind the rear pressure bulkhead.

    The front, usually fixed section of the tailplane is called the horizontal stabilizer and is used to balance and share lifting loads of the mainplane dependent on centre of gravity considerations by limiting oscillations in pitch. The rear section is called the elevator and is usually hinged to the horizontal stabilizer. The elevator is a movable airfoil that controls changes in pitch, the up-and-down motion of the aircraft's nose.

    On some aircraft, the horizontal stabilizer and elevator are combined into one movable unit called the stabilator or sometimes "flying tail" (see Anderson, John D., Introduction to Flight, 5th ed, p 517). In all cases some arrangement is made for the provision of trim to allow minor adjustment of airflow over the control surface and to unload the pilot from the need to maintain constant pressure on the elevator control. The trim may take the form of trim tabs on the rear of the elevators which act to force the elevator in the desired direction, or the stabilizer may be hinged at its trailing edge, forward of the elevator and adjustably jacked a few degrees in incidence either up or down. Early aircraft had a spring in the control circuit which provided an adjustable preload in the desired direction.

    The vertical tail structure, or fin, also has a fixed front section called the vertical stabilizer, used to prevent the aircraft from yawing from side to side. The rear section of the vertical fin is the rudder, a movable airfoil that is used to turn the aircraft in combination with the ailerons.

    Occasionally the horizontal stabilizer may carry more than one fin and rudder (Avro Lancaster, Lockheed Constellation) or the stabilizer and fin may be combined into a "V" shaped structure (Ruddervators) with each of the angled airfoils performing both functions (Beechcraft Bonanza 35, Fouga Magister). Frequently the horizontal stabilizer is mounted atop the fin (Boeing 727, Piper Tomahawk) Additional fin area may be added to aircraft fitted with floats (seaplanes) usually beneath the horizontal stabilizer (ventral fin) and sometimes at the stabilizer extremities.

    Multi engined and some light aircraft also include trim tabs on the rudder when asymmetric forces would impose unusual loads on the pilot's rudder controls.


    Trim tabs are small surfaces connected to the trailing edge of a larger control surface on a boat or aircraft. The angle of the tab relative to the larger surface can be adjusted to null out hydro- or aero-dynamic forces and stabilise the boat or aircraft in a particular desired attitude without the need for the pilot to constantly apply a control force.

    When mounted on a control surface (such as an elevator or rudder), the trim tab allows the pilot to easily adjust the position of the control surface, and to adjust the large force generated by the control surface. The trim tab acts as a servo tab. Because the center of pressure of the trim tab is further away from the axis of rotation of the control surface than the center of pressure of the control surface, the moment generated by the tab can match the moment generated by the control surface. The position of the control surface on its axis will change until the moments from the control surface and the trim surface balance each other.

    Uses in boats: Boats with planing-type hulls will often have trim tabs attached to the trailing edge of the hull or transom. These are used to adjust the pitch attitude of the boat while underway. Changes in boatspeed or weight placement will usually require the trim tabs to be adjusted to keep the boat at a comfortable and efficient pitch attitude. This reduces the work of the captain by reducing the amount of manual control necessary, as well as providing for greater efficiency by keeping the ship in the ideal orientation for the conditions.

    Uses in aircraft: Many airplanes (including gliders) have trim tabs on their elevators, this being a simple method of providing trim in the lateral axis.

    Source: Wikipedia (All text is available under the terms of the GNU Free Documentation License and Creative Commons Attribution-ShareAlike License.)

    Useful Links
    Science Fair Projects Resources
    Engineering Science Fair Books

                  





    My Dog Kelly

    Follow Us On:
         

    Privacy Policy - Site Map - About Us - Letters to the Editor

    Comments and inquiries could be addressed to:
    webmaster@julianTrubin.com


    Last updated: June 2013
    Copyright © 2003-2013 Julian Rubin